Melon Helmets Urban Active User Manual

 

Congratulations on your purchase of this Melon® Helmet!

The Melon® Urban Active Helmet represents the highest quality of protection against outside impacts against the head, be that whilst riding a bicycle, pedelecs, skates, inline blades or skate boards (Fig. 4). IMPORTANT: A helmet can only function as it was designed to when it is worn correctly, has been adjusted to fitted the users head and is carefully fastened. HOWEVER it is not possible to guarantee that a helmet can protect the wearer against all possible impacts. Melon® Urban Active Helmets are tested and certified to surpass the current official safety standards. CAUTION! This helmet should not be used by children while climbing or doing other activities where there is a risk of hanging or strangulation if the child gets trapped whilst wearing the helmet. We encourage you to make certain that your child removes the helmet before playing on or in Playgrounds, or similar areas. Please make sure to read this user manual in its entirety before use. These instructions build an integral part of the product.

This is why we encourage you to keep these instructions as well as the original packaging in safe keeping, should questions arise at a later stage.

 

TECHNICAL SPECIFICATIONS

Item: Melon® Urban Active Helmet

Sizes: XXS-S (46-52cm), M-L (52-58cm), XL-XXL 58-61cm)

 

WHICH HELMET SIZE IS BEST FOR ME AND HOW DO I ADJUST THE HELMET TO IT?

Your Melon® helmet can only offer its total protective potential when it has been

adjusted correctly and fits superbly (Fig. 2). The helmet is designed to be retained by

a strap under the lower jaw. Please test several helmet shell sizes in order to compare, also measure your head with a tape measure to double-check the size you have against the chart on the side of the packaging. We recommend choosing the helmet shell that fits firmly, but comfortably on the head. The helmet should not move or

wiggle additionally when you shake your head. Take the helmet in the chosen size and turn the adjustment ring in an anti-clockwise direction until it reaches its largest position. Now place the helmet on your head. If the helmet is too loose, then first exchange the breathable Coolmax® padding set of the helmet with the next larger size (Fig. 5). Should the helmet still be too loose exchange those against the next larger padding set. The different padding sets can also be combined to create intermediate sizes.

The Spin-Dial size adjuster should only be used to further fine tune the fit (Fig. 3a).

To tighten the helmet you turn the dial in a clockwise direction. To loosen, turn the dial in an anti-clockwise direction. Once the right size is found and adjusted correctly,

the helmet should sit firmly, but comfortably on the head.

 

WHEN DOES THE HELMET FIT PROPERLY?

The helmet should surround the head easily, and should be worn level.

The front helmet edge should sit 2 finger widths above the bridge of the nose (Fig. 2).

It is easy to check if the helmet fits correctly. All you must do is leave the chinstrap undone, and shake your head. If the helmet moves, then we recommend tightening the helmet ring and / or using thicker paddings.

 

HOW DO I ADJUST THE CHINSTRAP CORRECTLY?

Position the Strap Adjuster (Fig. 3b) in such a way that either junctions or the straps themselves touch your ears. To adjust the straps correctly it is imperative to make sure to adjust both left and right straps evenly to the right length. To do this open the strap lock on each Melon® Strap Adjuster. Please notice that the rear strap should be longer than the front (Fig. 2). Once the right length has been found please close these locks. Additionally the right side chinstrap can be shortened in its entirety, by pulling it further through the Fidlock® magnetic buckle loop (Fig. 3c).

To check for correct fit, place helmet on head and make any adjustments indicated. Securely fasten retention system. Grasp the helmet and try to rotate it to the front and rear. A correctly fitted helmet should be comfortable and should not move forward to obscure vision or rearward to expose the forehead.

 

HOW DOES THE FIDLOCK® MAGNETIC BUCKLE WORK?

The Melon® urban active helmets come fitted with Fidlock® magnetic closure systems. These are very simple to use and close by placing both ends on top of each other.

To open the closure, simply push the outside part in the direction of the arrow (Fig. 3c).

 

CONNECTOR OPENINGS & IMPACT BLOCKER SLOT

Your Melon® helmet has small bays at the front helmet edge for Melon® accessories such as the Melon® Vista Visor UV400 (Fig.6), which can be purchased as an accessory. For more information visit www.melon-helmets.com.

 

VISIBILITY ALSO AT NIGHT

The Melon® helmet has reflective logos at the front and the back,

made of high quality 3M reflective material.

 

WARNING

• The Melon® Urban Active Helmets are not designed to be used with petrol powered
   push bikes/mopeds/scooters or vehicles which are classed as Motor cycles.

• Before setting off, always make sure the chinstrap is closed.

• The helmet is not to be painted or have stickers stuck on its surface.

   This is because the helmet may damaged and rendered ineffective by petroleum

   products, cleaning agents, paints, adhesives and the like, without the damage being
   visible to the user.

• The helmet should be checked in regular intervals for damage.

   Small indentations and scratches on the surface however should not reduce the
   overall protective effect, if not effected by severe blow.

• The helmet is designed to absorb shock by partial destruction of the shell and liner.
   This damage may not be visible. Therefore, if subjected to a severe blow, the helmet
   should be destroyed and replaced even if it appears undamaged.

• When repairing (repairable damage!) any part of the helmet. Use only original parts!

• The helmet is not to be stored or hung up, hanging from the chinstrap.

• You should avoid wearing the following under your helmet: headscarves, beanies,
   long hair in a bun, or similar, as this could lead to subsequent injuries.

• No attachments should be made to the helmet except those recommended by the
   helmet manufacturer.

• CAUTION! This helmet should not be worn during activities where a risk of

   strangulation is high through capture, such as climbing.

 

HOW DO I LOOK AFTER MY HELMET PROPERLY?

Clean this helmet only with a mild detergent and warm water or a damp cloth.

The Coolmax® pad sets can be machine washed with a gentle detergent at 30˚C.

These must be drip dried at room temperature.

 

HOW LONG CAN I USE THIS HELMET SAFELY?

All components of this helmet are exposed to use.

Dependent on the use, care and maintenance the time to replace such a helmet is difficult to calculate or predict, but we recommend that a replacement should be done between 3 and 5 years of use. When storing this helmet, make sure it is stored safely, in an area where it is protected from direct sunlight and weather influences. So that it can’t be damaged or potentially hurt others, through falling. We advise strongly for your own safety to only use original parts. Should any part of the shell be broken or have sharp indentations to it or show obvious signs of wear, then the helmet must be replaced as it is no longer fit for use. If you are in doubt please get in contact with our service team through www.melon-helmets.com

 

DISPOSAL NOTE

Please take your helmet to an appropriate disposal facility at the end of its useful life. The disposal company on site, should answer questions you may have about the

actual disposal.

 

SERVICE

In purchasing a Melon® Urban Active Helmet you have purchased a proven high quality brand product. Should you notice anything that is not up to our high standards, then please return the helmet as soon as possible to your dealer of trust for a refund.